We got a wedding gun.
A long-standing interest in firearms resurfaces with a new piece from a family wedding, alongside reflections on collecting in the author's twenties and thirties.
Long-running personal blog from Chris Mapp: snack-food tastings, retro action figures, building blocks, fishing on the Chesapeake Bay, and the occasional pop-culture reflection.
A long-standing interest in firearms resurfaces with a new piece from a family wedding, alongside reflections on collecting in the author's twenties and thirties.
A new addition to the collection from January 2016, documented with the usual mix of photography and childhood-toy nostalgia.
Holiday recap from December 2015 covering Christmas gifts, Star Wars Episode VII chatter, and the Town of Exmore Christmas Parade.
A November 2013 review of an affordable knockoff building set, set alongside the author's decades-long love of Lego and Christmas-movie building marathons.
July 2013 entry on a bounty hunter figure acquired via trade with LeAnn of Retro Toy Safari, as the Star Wars Power of the Force 2 collection grows.
August 2013 tasting notes on a childhood favourite cereal, plus reflections on how many cereals have changed over the years.
A June 2013 League of Extraordinary Bloggers prompt on summer memories, fishing on the Chesapeake Bay, and learning the water from a 16-foot wooden scow.
A pneumatic lubricator delivers oil or grease through repeated pump strokes, with compressed air providing the driving force. Selecting the correct stroke frequency determines whether moving parts receive a reliable film of lubricant or become flooded with excess oil. The calculation is straightforward once the required lubricant volume, pump displacement and operating conditions are known.
For Australian manufacturing and maintenance teams, the practical answer must account for long pipe runs, seasonal temperature changes, dusty worksites and the availability of imported components. A setting that works on a clean workshop test bench may need adjustment on a conveyor in Brisbane, a processing line in Melbourne or heavy equipment operating in the Pilbara.
Stroke frequency is the number of delivery strokes completed during a set period, normally strokes per minute or strokes per hour. It controls the rate at which lubricant reaches a bearing, slide, chain, gear, guide or other friction point. Too few strokes can cause oil starvation, friction and premature wear. Too many can create heat, contamination, leakage and unnecessary lubricant consumption.
A pneumatic pump may be rated for a maximum number of cycles, but that rating is not automatically the correct operating speed. The correct value comes from the lubrication demand of the machine. A slow, heavily loaded slide may need a small and regular dose, while a fast chain or high-temperature bearing may require a different delivery pattern.
Galling is a particular concern where metal surfaces slide against one another under load. A properly controlled oil film reduces direct contact and helps manage wear, as explained in this guide to the role of lubrication. The aim is consistent dosing rather than simply increasing pump activity.
Start with the required lubricant volume. This may be stated by the equipment manufacturer as millilitres per hour, millilitres per cycle, grams per hour or a quantity per operating shift. If the specification gives a quantity per machine cycle, multiply it by the number of cycles per hour. For example, 0.02 mL per cycle at 180 cycles per hour requires 3.6 mL of lubricant per hour.
Next, identify the pump’s effective displacement per delivery stroke. Use the manufacturer’s measured output where possible, rather than relying only on a nominal catalogue figure. Pneumatic oil pumps can deliver less than their theoretical volume because of air compression, seal friction, line resistance, oil viscosity and back pressure.
You will also need to know whether the pump delivers on one direction of movement or on both. Some units discharge once per complete air cycle, while others provide a dose during each extend and retract stroke. Check the technical sheet for the difference between an air stroke, a pump stroke and a complete cycle. Confusing these terms can double or halve the calculated frequency.
The basic formula is:
Stroke frequency = required lubricant flow ÷ effective volume delivered per stroke
When the required flow is in millilitres per hour and the pump output is in millilitres per stroke, convert the result into strokes per minute:
Strokes per minute = required flow in mL/h ÷ effective stroke volume in mL ÷ 60
The effective stroke volume should include a delivery factor for real operating losses. A useful calculation is:
Effective stroke volume = nominal stroke volume × delivery efficiency
For a clean, short installation with light oil, an efficiency factor of 0.9 may be reasonable. A longer hose, restrictive nozzle, cold oil or high back pressure may justify a lower factor such as 0.75 or 0.8. Use test measurements when the lubrication point is critical.
If the pump produces two delivery strokes per complete pneumatic cycle, divide the required stroke frequency by two to obtain the air-cycle frequency. This distinction matters when setting a timer, solenoid valve or pneumatic controller.
Suppose a slide requires 6 mL of oil every hour. The pneumatic metering pump has a nominal output of 0.08 mL per stroke, and testing suggests an 85 percent delivery efficiency.
First calculate the effective volume:
0.08 × 0.85 = 0.068 mL per stroke
Then calculate the hourly stroke requirement:
6 ÷ 0.068 = 88.2 strokes per hour
Convert this to strokes per minute:
88.2 ÷ 60 = 1.47 strokes per minute
The practical setting would be approximately 1.5 delivery strokes per minute, or one stroke every 41 seconds. If the pump delivers on both directions of a complete air cycle, the controller would need about 0.74 air cycles per minute, subject to the manufacturer’s control method and minimum operating interval.
Avoid rounding too early. A pump set to one stroke per minute would deliver roughly 4.08 mL per hour under these assumptions, while two strokes per minute would deliver about 8.16 mL per hour. The difference may be significant on a small bearing or precision slide.
Temperature can change the actual dose. Oil becomes more viscous during a cold winter start in regional Victoria or Tasmania, increasing resistance through small-bore tubing and metering nozzles. In tropical Queensland, heat may reduce viscosity and increase leakage at worn seals. Measure the output at the expected operating temperature if consistent dosing is important.
Air pressure also affects performance. Pressure below the pump’s recommended range may prevent a full stroke, while excessive pressure can increase impact, leakage or lubricant consumption. A regulator, gauge and filter should be installed close enough to the pump to provide stable supply conditions. Compressed air quality matters too, especially where water or compressor oil could contaminate the lubricant.
For a dusty conveyor or mobile plant operating near a Western Australian mine, protect the reservoir breather, fittings and hose connections from contamination. Long distances between a Shenzhen distributor and an Australian worksite can make replacement parts a planning issue, so record the pump model, seal material, nozzle size and hose specification before ordering spares.
A calculation is a starting point, not a substitute for commissioning. Run the system at the intended pressure and temperature, then collect the discharge from the final nozzle over a measured period. Compare the collected volume with the theoretical delivery and revise the efficiency factor if necessary.
Inspect the lubrication point after several operating hours. A healthy application should show a controlled film without dripping, spray, heavy build-up or dry contact marks. Look for rising bearing temperature, unusual noise, scoring and lubricant leakage. On a paper-converting or packaging line, reliable dosing can protect rollers and guides; examples of paper processing equipment show why machinery-specific operating conditions must be considered.
Use a simple record sheet for each point. Note the lubricant grade, pump displacement, air pressure, hose length, nozzle type, stroke interval and observed condition. This is particularly useful for Australian sites with rotating maintenance crews, remote assets or contractors who may describe settings in different ways.
Select the nearest available timer setting only after checking the actual dose and machine response. Keep the final calculation with the equipment records, and label the controller with the stroke interval as well as the air pressure range. Contact the lubrication-system distributor with those measured details when you need a replacement pump, nozzle, hose or spare part, so the supplied component matches the real application rather than just the original catalogue description.
Star Wars Power of the Force 2 figures, Lego and knockoff building block reviews, and trades with fellow collectors.
Read toy posts →Weekly snack food and restaurant spotlights, from Hostess Fruit Pies to Froot Loops Treasures and beyond.
Read food posts →Summer vacations, fishing on the Chesapeake Bay, local community events, and other personal reflections.
Read life posts →